Flat 4 Tilbury House
9, Myers Lane LONDON SE14 5RY
Total floor area
31 square metres
Rules on letting this property
Properties can be let if they have an energy rating from A to E.
You can read
guidance for landlords on the regulations and exemptions.
Breakdown of property’s energy performance
This section shows the energy performance for features of this property. The assessment does not consider the condition of a feature and how well it is working.
Each feature is assessed as one of the following:
very good (most efficient)
very poor (least efficient)
When the description says “assumed”, it means that the feature could not be inspected and an assumption has been made based on the property’s age and type.
Cavity wall, as built, insulated (assumed)
Fully double glazed
Boiler and radiators, mains gas
Main heating control
Programmer, room thermostat and TRVs
From main system
Low energy lighting in 60% of fixed outlets
(another dwelling above)
Solid, limited insulation (assumed)
Primary energy use
The primary energy use for this property per year is 202 kilowatt hours per square metre (kWh/m2).
What is primary energy use?
Primary energy use is a measure of the energy required for lighting, heating and hot water in a property. The calculation includes:
the efficiency of the property’s heating system
power station efficiency for electricity
the energy used to produce the fuel and deliver it to the property
Environmental impact of this property
This property’s current environmental impact rating is C. It has the potential to be B.
Properties are rated in a scale from A to G based on how much carbon dioxide (CO2) they produce.
Properties with an A rating produce less CO2 than G rated properties.
An average household produces
6 tonnes of CO2
This property produces
1.1 tonnes of CO2
This property’s potential production
1.0 tonnes of CO2
By making the
recommended changes, you could reduce this property’s CO2 emissions by 0.1 tonnes per year. This will help to protect the environment.
Environmental impact ratings are based on assumptions about average occupancy and energy use. They may not reflect how energy is consumed by the people living at the property.
Improve this property’s energy performance
By following our step by step recommendations you could reduce this property’s energy use and potentially save money.
Carrying out these changes in order will improve the property’s energy rating and score from C (74) to C (76).
Do I need to follow these steps in order?
Yes. Each step builds on the one before it so you can save the most energy.
For example, it’s more energy efficient to insulate your home before you buy a new boiler. A well insulated home will lose less heat so you do not have to run your boiler as often.
Step 1: Floor insulation (solid floor)
Floor insulation (solid floor)
Typical installation cost
£4,000 - £6,000
Typical yearly saving
Potential rating after completing step 1
75 | C
Step 2: Low energy lighting
Low energy lighting
Typical installation cost
Typical yearly saving
Potential rating after completing steps 1 and 2
76 | C
Estimated energy use and potential savings
Estimated yearly energy cost for this property
The estimated cost shows how much the average household would spend in this property for heating, lighting and hot water. It is not based on how energy is used by the people living at the property.
The potential saving shows how much money you could save if you
complete each recommended step in order.
For advice on how to reduce your energy bills visit
Simple Energy Advice. Heating use in this property
Heating a property usually makes up the majority of energy costs.
Estimated energy used to heat this property
2128 kWh per year
1427 kWh per year
Potential energy savings by installing insulation
The assessor did not find any opportunities to save energy by installing insulation in this property.
Contacting the assessor and accreditation scheme
This EPC was created by a qualified energy assessor.
If you are unhappy about your property’s energy assessment or certificate, you can complain to the assessor directly. If you are still unhappy after contacting the assessor, you should contact the assessor’s accreditation scheme. Accreditation schemes are appointed by the government to ensure that assessors are qualified to carry out EPC assessments. Assessor contact details
Accreditation scheme contact details
Elmhurst Energy Systems Ltd
01455 883 250
No related party
Date of assessment
21 March 2019
Date of certificate
25 March 2019
Type of assessment
Show information about the RdSAP
RdSAP (Reduced data Standard Assessment Procedure) is a method used to assess and compare the energy and environmental performance of properties in the UK. It uses a site visit and survey of the property to calculate energy performance.
This type of assessment can be carried out on properties built before 1 April 2008 in England and Wales, and 30 September 2008 in Northern Ireland. It can also be used for newer properties, as long as they have a previous SAP assessment, which uses detailed information about the property’s construction to calculate energy performance.
Other certificates for this property
If you are aware of previous certificates for this property and they are not listed here, please contact us at
or call our helpdesk on firstname.lastname@example.org 020 3829 0748.